Schlage master key generator mac#

This is not a real master key but rather the position in the example KBA.

Knowledgeable persons reading this article will notice that the top master key is cut '11111'.

These charts eliminate guesswork out of explanations above. Lower lever master keys are developed by using a combination of top level master key cuts and cuts used by a group of change keys, In a five space master key system, horizontal master keys, vertical master keys, page master keys master keys which operate four pages of change keys can be developed. In addition to the 1024 change key cuts and single master key cuts, numerous other key cuts are available which can be used to lower level master keys. Since one of the key cuts is used for the top master key, four key cuts are available for the KBA key cut chart. When using every other cut, master key systems are restricted to using cuts of 0/2/4/6/8 or 1/3/5/7/9. 030'.Īnother factor is that most lock manufacturers use a depth numbering system of 0-9 or 1-10 (ten increments). In order to solve this problem, manufacturers suggest using thicker master pins of at least. 015' master pins are quite thin and may cause cylinders to malfunction in heavy use. In order to set up a master key system, thin master pins are inserted on top of normal bottom pins to form two shearlines. 015' from one cut depth to the next deepest cut. Most lock companies normally use depth increments of.

Schlage master key generator mac#

While the cut numbers will be part of the 1024 generated key cuts, usually approximately 10% of the 1024 key combination cannot be used because of MAC problems.Įach lock company has developed their own rules for which numbers can be used in a KBA chart. Each company has a set maximum adjacent cut value (MAC) which is usually '7'. Metal removed from the deep cut does not allow for metal to support the adjacent shallow cut. One last consideration is that most lock system will not allow a very deep cut next to a very shallow cut. In a five pin master key system, using four change key cuts per space the total number of individual keys can be determined by the formula four (cuts) raised to the fifth power (spaces) equal 1024 total individual key cuts. When all five spaces have been rotated the final cut number would be 45552 according to the KBA and no further individual keys cuts are available.

Key cuts 32223, 32323, 32423 & 32533 can be developed.Īs with the vehicle odometer example, when those four key cut numbers have be used, Progression sequence '1' begins with the next column cut number '3' cut and rotation begins again using the next SOP rotation number ('2'). Cut numbers from other columns do not change at this time. The master key cut is a '1' cut, so there are four available numbers which can be rotated- 2/3/4/5. In the chart one example, rotation '1' is in the third space. While master key numbering systems are generated in a similar fashion, there are usually approximately only four choices of numbers which can be used for rotation. In the vehicle example, when the SOP number reaches '99999' no additional numbers are available without causing duplicate numbers. SOP in a vehicle odometer can be thought of as 54321 where the right dial is constantly rotating and the left dial changes least often. Uniformly, rotation '3' begins changing each time rotation '2” reaches '9', rotation '4' begins changing each time rotation '3' reaches '9' and rotation '5' changes each time rotation '4 reaches '9'. Rotation '2' changes each time rotation '1' returns to the '0' position and starts to rotate again through the numbers. As the vehicle moves ahead, rotation '1' constantly changes from '0' through '9'. Vehicle odometers operate in units of 10. SOP can be readily explained by studying the odometer in any vehicle. The bottom row shown in red shows the sequence of progression (SOP) for this master key system. Chart 1 shows an example KB A with the top row showing the masterkey cuts- 11111, and the vertical rows showing the change key cuts to be used with each masterkey cut. A key bitting array consists of the masterkey cuts to be used, the change key cuts and the order they are to be used in each space, and the sequence of progression (SOP). Terms used in this article may not conform to tightly held terms used by others but are meant to provide the simplest explanation of a complex subject. Building any master key system begins with a plan, often called a key bitting array (KBA).